Unfortunately, you need to keserítselek, these conditions can not weld aluminum, but question is what are you waiting for the kötéstől.
I want to ask for help from you in connection with welding aluminum, or just tips. I apologize in advance because they do not really know the technical words that my dad can weld, I'm just trying to get info about it.
To welded aluminum tube wall thickness of 2mm. So far, Mig machine 140es tried, but as I was reading after this operation to be 100% argon gas, we only have 82% rate, we used to have medical welding. The other problem was that the 3-meter cable work could not be deferred to the thread not always begyűrte the machine. I do not know that these conditions did succeed with the aluminum welding.
The other question which perhaps higher hopes: coated electrode welding machine can be alut weld? Because it sticks to this, we found a Mig machine managed to solve that DC can be welded (I was told the store and DC should be added), but can not drag curve can not be welded to it.
Even the machine was coated electrodes if all goes alternating current, so it does not even try, given the advice.
Either method can be solved in the welding of aluminum, or rather forget?
Maybe we could even try to acetylene, but we are afraid because of the thin wall thickness to flow away.
Unfortunately, a good metal-arc welding of aluminum pulse arc welding machine is needed to set start current to control the heat input, or low-frequency modulation of the output pikkelyezett seamless image.
Traditional switch level can not be nice aluminum welding machine to weld seam.
Can not just go to the DC argon welding aluminum eshez but Helium
What you should know before you start him Helium Helium cylinders and regulator should be about 1.5szer anyi Helium as Argon tried this a few words to say to my own experiences.
The arc is much more difficult for about 3 seconds elofujas very close and razor sharp wt20 tungsten (razor sharp I can understand the cross-section * 2 height KUP is polishing a rough 25 degrees if not less) that if you have the arc is almost like it would be like the stainless steel welding anyi difference that faster mer the helium-welded aluminum melt efficiently ....
how many amps should be about as inoxnal szenacelnal is lower than 10%. stainless steel with 5-6 l / p argon there Helium aluminum 8-10 l / p 6-7 Flow of ceramic and tungsten 1.6 if possible (easier ignition) after fulyas more time for verbal language is about 3-5 seconds
What to watch?
DC - inch razor sharp tungsten were not so tight as to hotartomanya aceloknal but not much thicker so hozanyagbol art 2-3.2es ajanlatos korkors kezmuzdalattal is better dispersed in the weld so hobevitel.
NE ilyedj here do not have to wait ACDCnel Arni as the bright aluminum surface to (break down the patina) of helium increased heat input because it's safe to carry out this work.
The material it is to know about weird behavior when compared to stainless steel as a top-bottom oblitogaz argon (mixing nitrogenargon) hegesztesz is like snot ... should be practiced en acdc who explicitly refers to aluminum welding and weld good enough or DC singer is thinking about whether it is worth it to suffer ... but 1 hour of practice you can feel and to me personally, did better than argon in the end because it AMCSi teknologia ... Many people must then read and Europe to find almost no mention of any ROLA is trying to be too much and you must feel
that it pays to or better than the argon hmm dependent persons
I wrote the Einhell not it? They describe a phone number to my colleague who is now an eye on the shop floor because he could not elhegeszteni a roll with it?
Where I bought the inverteremet, but only because they sell such a thing even if it is more expensive, do not even go to the store in person, but they can tell it's not the detail of the machine should be mentioned neked.Nem hundreds of thousands of machines, but if a machine is half as kispóroltak something from the other. The Germanic-sounding, CHINA !!!!!! Gude
aluminum instead of copper windings, of course, measure the settling and taknyol instead of welding. This is my colleagues who told him befürdött.
90-I do not understand that a lot of CO in the week.
The most important of the welding is not like a hair dryer that turns on anyone and there you go.
It's like a pencil, get a pencil portrait drawing does not make you a graphic Lake. Not discouraged I wanted, but once you have bought 1-2 machines there is no escape do not you let loose your invested money and just more expense Vered magad.Már I prefer board fence would build but there is snow 6 meters lengths of hundreds of thousands sought, and the tools of money.